Emerson Process Management Series 100 Gas Analyzers HYDROS 100 Manual de usuario Pagina 118
- Pagina / 225
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
8 - 12
ENTRY OF SYSTEM PARAMETERS
ETC00265(4) Series 100 e 02/2004
8.14 Reset
The reset operation restores the settings of the analyzer to the parameters and calibration factors
set in our factory at the time of its manufacture.
This is equivalent to switching off the electrical supply line and switching off the battery buffering
of the RAM’s by removing the battery jumper, J7.
All parameters and calibration factors entered by the user will be lost whenever a reset
operation is performed.
The currently valid user identification code must be entered before a reset will be executed; this
will prevent inadvertent resets.
Entry is performed using
followed by
Whenever a reset operation is initiated, the analyzer operating program will be restarted, just as
it is when the instrument is first switched on (see chapter 6).
Jumper J6, which activates the watchdog circuitry must be inserted if the
reset operation is to be correctly executed.
RESET
- Series 100 Gas Analyzers 1
- ESSENTIAL INSTRUCTIONS 2
- Safety Summary 3
- SUPPLY VOLTAGE 7
- SAFETY SUMMARY 10
- 100 (M/2M) and OXYNOS 12
- General Overview 17
- Area Classification 19
- Table of Contents 21
- CONTENTS 22
- 6. SWITCHING ON 6 - 1 23
- 7. KEY FUNCTIONS 7 - 1 23
- 9. CALIBRATION 9 - 1 24
- 11. DIGITAL OUTPUTS 11 - 1 24
- 1. Technical Description 31
- Needle valve (option) 33
- only possible if FOUNDATION 39
- Fieldbus is not request ! 39
- TECHNICAL DESCRIPTION 41
- INTERNAL CONSTRUCTION 41
- (channel 2) 42
- (channel 1) 42
- (Channel 1) 47
- (Channel 2) 47
- not for BINOS 57
- 100 F in hazardous areas 57
- 2. Measuring Principle 59
- MEASURING PRINCIPLE 60
- Interference Filters used 60
- IR MEASUREMENT 60
- OXYGEN MEASUREMENT (PO 64
- PARAMAGNETIC PRINCIPLE) 64
- OXYGEN MEASUREMENT (EO 66
- ELECTROCHEMICAL PRINCIPLE) 66
- concentration in the gas 67
- 3. Photometer Assembly 71
- PHOTOMETER ASSEMBLY 72
- PYROELECTRICAL DETECTOR 72
- GAS DETECTOR 74
- 16 5 4 623 75
- 5. Preparation of Start-up 77
- PREPARATION 79
- GAS CONNECTIONS 81
- Wall mounting holder 83
- Fig. 5-4a: BINOS 84
- 100 F / CONTINUOUS PURGE 86
- 100 F / Z PURGE 87
- X2 Analog out 92
- X3 Digital out 92
- X1 Status 92
- 6. Switching On 93
- SWITCHING ON 96
- 230/120 V AC SUPPLY 96
- 7. Key Functions 99
- KEY FUNCTIONS 100
- FUNCTION 100
- Interface 101
- CODE: factory setting “1” 103
- Touch screen release: 103
- DOWN, UP, ENTER, FUNCTION 103
- INPUT - CONTROL 104
- 8. Setting System Parameters 107
- SETTING SYSTEM PARAMETERS 108
- SETTING SYSTEM PARAMETERS 109
- HOLD / AUTOMATIC CALIBRATION 110
- TOLERANCE CHECK 111
- DISPLAY OFF 112
- ANALOG SIGNAL OUTPUTS 113
- FLUSHING PERIOD / USER CODE 114
- RESPONSE TIME (T 115
- ENTRY OF SYSTEM PARAMETERS 116
- OFFSET (BEGIN OF RANGE) 116
- ENTRY OF SYSTEM PARAMETERS 117
- END OF RANGE VALUE 117
- GAS SAMPLING PUMP 120
- 9. Calibration 121
- CALIBRATION 122
- MANUAL ZEROING 122
- MANUAL SPANNING 124
- AUTOMATIC ZEROING (OPTION) 127
- MEASUREMENT/SWITCHING OFF 131
- MEASUREMENT 131
- MEASUREMENT/SWITCHING OFF 132
- SWITCHING OFF 132
- 11. Digital Outputs 133
- DIGITAL OUTPUTS 134
- CONCENTRATION LIMITS 134
- LIMIT VALUES 135
- Rosemount Analytical 137
- SERIAL INTERFACE (OPTION) 146
- INSTRUCTION SYNTAX 147
- RESPONSE TELEGRAMS 149
- Fieldbus (BINOS 151
- DIGITAL INPUTS / FOUNDATION 152
- FIELDBUS (OPTIONS) 152
- CROSS COMPENSATION 153
- Table 14-1: Solder bridges 154
- CROSS COMPENSATION 155
- 16. List of Failures 157
- LIST OF FAILURES 164
- (at BAF 01) 171
- (D 30 at BKS) 171
- orange 176
- yellow 176
- FINE DUST FILTER (OPTION) 180
- 22. Leak Testing 181
- LEAK TESTING 182
- 23. Housing 183
- LIGHT SOURCE REPLACEMENT 190
- CLEANING 192
- PHYSICAL ZEROING 195
- CHECKING THE SENSOR 198
- Tp 1 Tp 2 198
- Front panel 200
- 27. Technical Data 205
- TECHNICAL DATA 206
- HOUSING / OPTIONS 206
- SIGNAL OUTPUTS, INTERFACES 207
- 462.6 52.5 208
- (connection cables) 209
- [all dimensions in mm] 209
- Cross sensitivities 211
- GENERAL SPECIFICATIONS 212
- VOLTAGE SUPPLY 213
- 275.3 105.9 214
- 28. Replacing the EPROM 215
- REPLACING THE EPROM 216
- 30. Cables and Cords 217
- CABLES AND CORDS 218
- FACTORY REPAIRFAILURE 223
- CHECK LIST 223
- Customer Service 224
- Training 224
Relacionado con productos y manuales para De medición, control y control Emerson Process Management Series 100 Gas Analyzers HYDROS 100
De medición, control y control Emerson Process Management - Emerson Electric Co. Ventilation Hood 7951 Manual de usuario
(204 paginas)
(204 paginas)
De medición, control y control Emerson Process Management ROSEMOUNT 5300 Manual de usuario
(324 paginas)
(324 paginas)
De medición, control y control Emerson Process Management IM-106-910Xi Manual de usuario
(126 paginas)
(126 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.172 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales