Emerson Process Management Series 100 Gas Analyzers HYDROS 100 Manual de usuario Pagina 110
- Pagina / 225
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
8 - 4
SETTING SYSTEM PARAMETERS
ETC00781(4) Series 100 e 02/2004
8.4 Hold
The analyzer function HOLD is used to lock the analog signal outputs and the concentration
limits during a calibration procedure to hold the last measured values.
Input value 0: The outputs remain unlocked.
Input value 1: The outputs will be locked.
Change values using
and
8.5 Automatic Calibration
For operation with optional, internal or external solenoid valves it can be selected, if there a time-
controlled (automatic) resp. a remote-controlled calibration is possible or not (in combination with
solenoid valves controlled via digital outputs).
Input value 0: Time-controlled / remote-controlled calibration is not possible
Input value 1: Time-controlled / remote-controlled calibration is possible
Change values using
and
HOLD / AUTOMATIC CALIBRATION
- Series 100 Gas Analyzers 1
- ESSENTIAL INSTRUCTIONS 2
- Safety Summary 3
- SUPPLY VOLTAGE 7
- SAFETY SUMMARY 10
- 100 (M/2M) and OXYNOS 12
- General Overview 17
- Area Classification 19
- Table of Contents 21
- CONTENTS 22
- 6. SWITCHING ON 6 - 1 23
- 7. KEY FUNCTIONS 7 - 1 23
- 9. CALIBRATION 9 - 1 24
- 11. DIGITAL OUTPUTS 11 - 1 24
- 1. Technical Description 31
- Needle valve (option) 33
- only possible if FOUNDATION 39
- Fieldbus is not request ! 39
- TECHNICAL DESCRIPTION 41
- INTERNAL CONSTRUCTION 41
- (channel 2) 42
- (channel 1) 42
- (Channel 1) 47
- (Channel 2) 47
- not for BINOS 57
- 100 F in hazardous areas 57
- 2. Measuring Principle 59
- MEASURING PRINCIPLE 60
- Interference Filters used 60
- IR MEASUREMENT 60
- OXYGEN MEASUREMENT (PO 64
- PARAMAGNETIC PRINCIPLE) 64
- OXYGEN MEASUREMENT (EO 66
- ELECTROCHEMICAL PRINCIPLE) 66
- concentration in the gas 67
- 3. Photometer Assembly 71
- PHOTOMETER ASSEMBLY 72
- PYROELECTRICAL DETECTOR 72
- GAS DETECTOR 74
- 16 5 4 623 75
- 5. Preparation of Start-up 77
- PREPARATION 79
- GAS CONNECTIONS 81
- Wall mounting holder 83
- Fig. 5-4a: BINOS 84
- 100 F / CONTINUOUS PURGE 86
- 100 F / Z PURGE 87
- X2 Analog out 92
- X3 Digital out 92
- X1 Status 92
- 6. Switching On 93
- SWITCHING ON 96
- 230/120 V AC SUPPLY 96
- 7. Key Functions 99
- KEY FUNCTIONS 100
- FUNCTION 100
- Interface 101
- CODE: factory setting “1” 103
- Touch screen release: 103
- DOWN, UP, ENTER, FUNCTION 103
- INPUT - CONTROL 104
- 8. Setting System Parameters 107
- SETTING SYSTEM PARAMETERS 108
- SETTING SYSTEM PARAMETERS 109
- HOLD / AUTOMATIC CALIBRATION 110
- TOLERANCE CHECK 111
- DISPLAY OFF 112
- ANALOG SIGNAL OUTPUTS 113
- FLUSHING PERIOD / USER CODE 114
- RESPONSE TIME (T 115
- ENTRY OF SYSTEM PARAMETERS 116
- OFFSET (BEGIN OF RANGE) 116
- ENTRY OF SYSTEM PARAMETERS 117
- END OF RANGE VALUE 117
- GAS SAMPLING PUMP 120
- 9. Calibration 121
- CALIBRATION 122
- MANUAL ZEROING 122
- MANUAL SPANNING 124
- AUTOMATIC ZEROING (OPTION) 127
- MEASUREMENT/SWITCHING OFF 131
- MEASUREMENT 131
- MEASUREMENT/SWITCHING OFF 132
- SWITCHING OFF 132
- 11. Digital Outputs 133
- DIGITAL OUTPUTS 134
- CONCENTRATION LIMITS 134
- LIMIT VALUES 135
- Rosemount Analytical 137
- SERIAL INTERFACE (OPTION) 146
- INSTRUCTION SYNTAX 147
- RESPONSE TELEGRAMS 149
- Fieldbus (BINOS 151
- DIGITAL INPUTS / FOUNDATION 152
- FIELDBUS (OPTIONS) 152
- CROSS COMPENSATION 153
- Table 14-1: Solder bridges 154
- CROSS COMPENSATION 155
- 16. List of Failures 157
- LIST OF FAILURES 164
- (at BAF 01) 171
- (D 30 at BKS) 171
- orange 176
- yellow 176
- FINE DUST FILTER (OPTION) 180
- 22. Leak Testing 181
- LEAK TESTING 182
- 23. Housing 183
- LIGHT SOURCE REPLACEMENT 190
- CLEANING 192
- PHYSICAL ZEROING 195
- CHECKING THE SENSOR 198
- Tp 1 Tp 2 198
- Front panel 200
- 27. Technical Data 205
- TECHNICAL DATA 206
- HOUSING / OPTIONS 206
- SIGNAL OUTPUTS, INTERFACES 207
- 462.6 52.5 208
- (connection cables) 209
- [all dimensions in mm] 209
- Cross sensitivities 211
- GENERAL SPECIFICATIONS 212
- VOLTAGE SUPPLY 213
- 275.3 105.9 214
- 28. Replacing the EPROM 215
- REPLACING THE EPROM 216
- 30. Cables and Cords 217
- CABLES AND CORDS 218
- FACTORY REPAIRFAILURE 223
- CHECK LIST 223
- Customer Service 224
- Training 224
Relacionado con productos y manuales para De medición, control y control Emerson Process Management Series 100 Gas Analyzers HYDROS 100
De medición, control y control Emerson Process Management - Emerson Electric Co. Ventilation Hood 7951 Manual de usuario
(204 paginas)
(204 paginas)
De medición, control y control Emerson Process Management ROSEMOUNT 5300 Manual de usuario
(324 paginas)
(324 paginas)
De medición, control y control Emerson Process Management IM-106-910Xi Manual de usuario
(126 paginas)
(126 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales